Appliance Repair in Windham, Ohio

Need Appliance Repair Service? Have a general question?
We love solving problems! Let us know how we can help by reaching out below.

How can we help?

Local Reviews
for Windham, OH

Rated 5.0 out of 5 stars based on 2 customer reviews

Map of Windham, OH

Great service




Very knowledgeable, and courteous!


Response from Fred's Appliance Service:

Hi Dolores, Thanks for the feedback! We pride ourselves in keeping our technicians up-to-date with the always changing industry! Have a great week! Thank you, The Fred's Team


Map of Windham, OH

Great Service





Robert A.

Robert A.

ROPER WASHER RTW4516FW2 Ran diagnostics, 81, no water, found unit not getting cold water, cleaned valve screens, tested valves, good, ran recal, op test ok; Job Cmpltd,

Near OH-303, Windham, OH 44288
Corina B.

Corina B.

WTW8800YC1 Whirlpool Washer CC that you sent the control on a cycle and it goes to a different cycle and the spin cycle is loud. When setting the cycle to a white load the control goes to a clean wash cycle. Ran a drain and spin and the bearings are bad. Will need a new control, UI hub and bearings. ; ordrng 1 W10435302 (bearing) and 1 W10761635 (cntrl-elec) and 1 W10820039 (hub) and 1 WPW10404675 (console)

Near Streeter Rd, Windham, OH 44288
Corina B.

Corina B.

WED8800YC1 Whirlpool Dryer Replaced the fuse. Customer has foil style vent advised the customer that it’s a potential fire hazard to replace with a semi rigid or rigid vent. Checked outside vent, good. Optest ok.

Near Streeter Rd, Windham, OH 44288
Robert A.

Robert A.

WHIRLPOOL DISHWASHER MDB7749AWW2 , Installed panel, handle and latch, op test ok; Job Cmpltd,

Near Belden Dr, Windham, OH 44288
Robert A.

Robert A.

WHIRLPOOL DISHWASHER MDB7749AWW2 Found handle and panel broken; ordrng 1 W10811149 (PANEL), schdld next appmnt for 3/27 TUE 12-4,

Near Belden Dr, Windham, OH 44288
Robert A.

Robert A.

WHIRLPOOL WASHER WTW8040DW2 Ran diognastics, off bal load, 9-2 drive pump fault, found no air gap in drain, drain filling up and siphoning water back into 7nit, needs drain correctedOp test ok;

Near Nichols Rd, Windham, OH 44288
Tim G.

Tim G.

WHIRLPOOL DRYER WED4850BW0 Complaint that the unit is not heating. Checked and found no power at the terminal block. Checked breaker and reset. Found 240vac present at the terminal block. Ran unit on a high heat and found to only run for a few seconds. Tried without heat and found same result. Checked and found the motor faulty (start and run not releasing from each other).replaced motor and tested, op test good. Cust has a foil accordion style vent hose attached to dryer (see pic). Explained the fire hazard associated with this type of vent hose and advised cust to replace with a semi­rigid metal hose to prevent fire hazard.; used 1 279827 (MOTOR) from stock, Job Cmpltd,

Near OH-700, Windham, OH 44288
Robert A.

Robert A.

WHIRLPOOL DISHWASHER WDP340PAFW0 Checked heater connections, good, ran diagnostics, no codes, excessive soap in unit, heater is working, cleared soap, op test ok; Job Cmpltd,

Near Cloverleaf Rd, Windham, OH 44288
Tim G.

Tim G.

MAYTAG WASHER MVWB850YW0 Complaint that the unit displays F51 (RPS failure). Checked and found the rotor bolt loose causing the error. Tightened and tested, op test NG bearings have failed. Replaced same, op test good. ; used 1 W10435302 (BEARING) from stock, Job Cmpltd,

Near Nichols Rd, Windham, OH 44288
Tim G.

Tim G.

MAYTAG WASHER MVWC565FW0 Complaint that the unit will not advance past wash. Checked and found a stored F8E1 long no fill error. Checked the valve and found very low cold water pressure into the unit. Found the screen blocked and cleaned, op test good.; Job Cmpltd

Near Nichols Rd, Windham, OH 44288
Tim G.

Tim G.

Maytag top load washer MVWC565FW0, Complaint that the unit will not advance past wash. Checked and found a stored F8E1 long no fill error. Checked the valve and found very low cold water pressure into the unit. Found the screen blocked and cleaned, op test good.

Near Co Hwy 225, Windham, OH 44288
Robert A.

Robert A.

MAYTAG WASHER MVWB835DW0 Complaint, wash tub overflowed, checked pressure hose, good, ran diagnostics, off bal, ran test 52, good, ran test 51 good, started normal wash fill is correct, found slow drain in sink needs plumber, op test ok; Job Cmpltd,

Near OH-88, Windham, OH 44288
Tim G.

Tim G.

MAYTAG WASHER MVWB835DW0 Installed new acu and UI. Ran a recal cycle, op test good. Customers was advised that they should have a plumber out to replace the shutoff valves for the water supply (see pic).; Job Cmpltd,

Near OH-88, Windham, OH 44288
Tim G.

Tim G.

Maytag top load washer MVWB835DW0, Installed new acu and UI. Ran a recal cycle, op test good.

Near OH-88, Windham, OH 44288
Robert A.

Robert A.

MAYTAG WASHER MVWB835DW0 Ran diagnostics f6e3 ui cannot hear acu, f6e2 acu can not hear ui, checked connections, good, checked harness, good, needs ui and acu; ordrng 1 W10812420 (ACU) and 1 W10861510 (UI), schdld next appmnt for 5/30 TUE !,

Near OH-88, Windham, OH 44288
Tim G.

Tim G.

MAYTAG WASHER MVWC565FW0 Customers complaint is that the unit will not fill with enough water on normal loads. Checked unit and found low pressure after the valve. Pulled valve found debris build up. Unit needs valve. ; ordrng 1 W11038689 (INLET VALVE ), schdld next appmnt for 5/18 THU !,

Near Smalley Rd, Windham, OH 44288
Tim G.

Tim G.

Maytag top load washer MVWC565FW0, Customers complaint is that the unit will not fill with enough water on normal loads. Checked unit and found low pressure after the valve. Pulled valve found debris build up. Unit needs valve.

Near Smalley Rd, Windham, OH 44288