Service History 1214 | Freds Appliance

We serviced a

WHIRLPOOL DISHWASHER

Model WDT720PADM2

Near Rocky River, OH 44116

Macaulay G.

Job Details: 01/25/2018

Found unit with water in it. Also found that unit was not leveled. Leveled unit and tested ok. Filled and drained several times, no restrictions or hesitation in drain. Control board not allowing unit to finish cycle. Office to order control board.; ordrng 1 W10854231 (cntrl-elec), schdld next appmnt for 2/6 TUE 8-11,

We serviced a

WDF330PAHW0 whirlpool

Model dishwasher

Near LaGrange, OH 44050

Paul H.

Job Details: 01/25/2018

Replace the gasket,ran diagnostics test, no leaks; Job Cmpltd,

We serviced a

MVWB725BW0 MAYTAG

Model WASHER

Near WARRENSVL HTS, OH 44122

Corina B

Job Details: 01/24/2018

Replaced the valve. Optest ok. ; Job Cmpltd

We serviced a

ASI257FRB00 AMANA

Model REFRIGERATOR

Near Cleveland, OH 44108

Dan

Job Details: 01/24/2018

Customer complaint that unit is leaking water, found unit leaking from connection at water filter housing, reset connection, no leaks now, op test good ; Job Cmpltd

We serviced a

WTW4816FW1 washer

Model whirlpool

Near Elyria, OH 44035

Paul H.

Job Details: 01/24/2018

Checking water level,running a diagnostics test,everything is functioning correctly ,no issues ; Job Cmpltd

We serviced a

MDG9206AWW whirlpool

Model dryer

Near Broadview Heights, OH 44147

Chad P.

Job Details: 01/24/2018

Found rear rollers have failing bearings and belt is cracked and worn. Needs both replaced.

We serviced a

WRF736SDAM14 whirlpool

Model refrigerator

Near North Royalton, OH 44133

Chad P.

Job Details: 01/24/2018

Installed mullion and door. Op test ok. ; Job Cmpltd,

We serviced a

JMW2427DS00 whirlpool

Model microwave

Near Concord Township, OH 44077

Jeff M

Job Details: 01/24/2018

The unit has a f2e1 shorted key pad. I flip the breaker the code came back. The connection in the panel are good the unit needs a new ui est only; ordrng 1 W10887865 (UI),

We serviced a

WDF520PADM7 WHIRLPOOL

Model DISHWASHER

Near Cleveland, OH 44113

Dan

Job Details: 01/24/2018

Customer complaint that unit is not heating, unit was at the end of its cycle when tech arrived, heater was on, dishes were dry, ran diagnostics no error codes codes, unit is operating as designed advised customer to run hot water in sink before starting unit; Job Cmpltd

We serviced a

WRX735SDBM04 WHIRLPOOL

Model REFRIGERATOR

Near Cleveland, OH 44107

Macaulay G.

Job Details: 01/24/2018

Replaced roller. Leveled refrigerator. Unit tests ok. Instructed on proper use of ice.; Job Cmpltd

We serviced a

WRF535SMBM00 WHIRLPOOL

Model REFRIGERATOR

Near Willoughby, OH 44094

Robert A.

Job Details: 01/24/2018

Installed frz door, op test ok; Job Cmpltd

We serviced a

KDTM404EBL1 MAYTAG

Model DISHWASHER

Near Pepper Pike, OH 44124

Tim G.

Job Details: 01/24/2018

Complaint that the unit leaks from the right side. Checked unit and found unit tilted forward causing to be not level. Lowered legs to raise front and tested, let unit complete a full rinse cycle and found unit now not leaking. Instructed the customer on detergent usage (2tbls) and loading. ; Job Cmpltd

We serviced a

KRFF302ESS01 WHIRLPOOL

Model REFRIGERATOR

Near University Heights, OH 44118

Corina B

Job Details: 01/24/2018

Replaced im. Filled, Optest ok; Job Cmpltd

We serviced a

WEE730H0DS0 WHIRLPOOL

Model RANGE

Near Cleveland, OH 44113

Dan

Job Details: 01/24/2018

Called whirlpool techline spoke to Ron, ran diagnostics found f8e0( blower fan speed too low) error code, blower motor resistance out of range, Installed new blower, op test good, file number 7721129195; Job Cmpltd

We serviced a

PFS22MISBWW GE

Model REFRIGERATOR

Near South Euclid, OH 44121

Corina B

Job Details: 01/24/2018

CC that the temp is not keeping. Ff 42 fz 11. Checked the control and found a burn mark on the connectors. Will need a new control from t/s. ; used 1 WR55X10942P (MAIN BOARD) Job Cmpltd

We serviced a

GW39LXUQ07 WHIRLPOOL

Model RANGE

Near Cleveland, OH 44102

Dan

Job Details: 01/24/2018

Customer complaint that lower drawer is stuck, opened drawer, found wheel had fallen off of left side of drawer,no damage to wheel, bolt or mount, reinstalled , drawer is opening and closing properly, op test good ; Job Cmpltd

We serviced a

AC01560AW AMANA

Model MICROWAVE

Near North Olmsted, OH 44070

Macaulay G.

Job Details: 01/24/2018

Magnetron tube is fractured. Needs replaced. Customer will buy new

We serviced a

KUDC10IXWH4 KITCHENAID

Model DISHWASHER

Near Ravenna, OH 44266

Robert A.

Job Details: 01/24/2018

Found ui not responding, reset connections, ran diognastic cycle, good, op test ok; Job Cmpltd

We serviced a

WTW5000DW1 WHIRLPOOL

Model WASHER

Near Richmond Heights, OH 44143

Tim G.

Job Details: 01/24/2018

omplaint that there is a abnormal sound when in agitation. Checked error codes and found none stored. Tested the unit in a agitation and spin. Found the sound to be a scraping sound. Checked and found the plastic blower on top of the motor to be warped and rubbing on the gearcase. Was able to smooth out and tested, op test good.; Job Cmpltd

We serviced a

MER8800FZ1 maytag

Model range

Near Middleburg Heights, OH 44130

Chad P.

Job Details: 01/24/2018

Cc that unit was making a ticking noise when pressed on. Unable to duplicate at this time. Advised that cooktop only mounts with two screws and does have play. Op test ok. ; Job Cmpltd,

We serviced a

KDFE104DSS5 kitchenaid

Model dishwasher

Near Parma Heights, OH 44130

Chad P.

Job Details: 01/24/2018

Found heater deactivated from failed wash motor. Reset control and activated heater. Ran service mode test. Op test ok. ; Job Cmpltd,

We serviced a

MVWX655DW0 maytag

Model washer

Near Parma, OH 44129

Chad P.

Job Details: 01/24/2018

Installed GEARCASE and hub. Op test ok. ; Job Cmpltd,

We serviced a

WTW4800XQ1 whirlpool

Model washer

Near Avon Lake, OH 44012

Paul H.

Job Details: 01/24/2018

Ran diagnostics, f7e7 unable to reach target rpm, f7e1 shifter fault, needs actuator, replaced from t-s, tested, op test ok.; used 1 WPW10006355 (ACTUATOR) from stock, Job Cmpltd

We serviced a

WRS586FIEE00 whirlpool

Model refrigerator

Near Concord Township, OH 44060

Jeff M

Job Details: 01/24/2018

Installed new part unit op tested good. I tasted the water ; Job Cmpltd

We serviced a

MMV4205DS4 MAYTAG

Model MICROWAVE

Near Westlake, OH 44145

Macaulay G.

Job Details: 01/24/2018

Replaced door switches and tested, no power throughout unit. Fuse was open. Replaced fuse from truck stock. Tested and heated ok.; used 1 W10138793 (FUSE, MICROWAVE) from stock, Job Cmpltd

We serviced a

WRT518SZFM00 WHIRLPOOL

Model REFRIGERATOR

Near Bay Village, OH 44140

Macaulay G.

Job Details: 01/24/2018

All functions normal with refrigerator. Explained to customer on how refrigerator functions. Customer understands that this is how it is supposed to operate.; Job Cmpltd

We serviced a

WRX735SDHZ00 WHIRLPOOL

Model REFRIGERATOR

Near Olmsted Township, OH 44138

Macaulay G.

Job Details: 01/24/2018

Replaced water inlet valve. Purged air and water from line. Tested ok.; Job Cmpltd

We serviced a

WDF560SAFM1 WHIRLPOOL

Model DISHWASHER

Near Avon Lake, OH 44012

Macaulay G.

Job Details: 01/24/2018

Dishwasher fills ok. Motor does not turn on. Found split winding in motor. Electronic control board is not advancing through cycles as designed. Office to order sump motor and control board. Marconi advised to order grommet and hose as well.; ordrng 1 W10445975 (hose) and 1 W11032770 (motor-pump) and 1 W11108143 (cntrl-elec) and 1 WPW10538166 (grommet), schdld next appmnt for 2/1 THU

We serviced a

KSSS48QKX00 KITCHENAID

Model REFRIGERATOR

Near Strongsville, OH 44149

Macaulay G.

Job Details: 01/24/2018

Replaced main electronic control board. Now getting proper voltage to inverter board, but inverter board not sending to compressor. Office to order inverter board.; ordrng 1 W10629033 (inverter box ), schdld next appmnt for 2/1 THU

We serviced a

MVWC565FW0 MAYTAG

Model WASHER

Near Streetsboro, OH 44241

Robert A.

Job Details: 01/24/2018

Ran diognastics, 0-5 off bal load, 7-6 motor fault, 7-7 did not hit target speed, basket spins free, checked motor and cap, reset connections, no burnt smell, tested tach, good, ran maual adj, good, ran spin, good, checked drain pump, good, checked drain hose, good, ran drain and spin, all tests good, per tech sheet, needs control; ordrng 1 W11116594 (CONTROL), schdld next appmnt for 1/31 WED

We serviced a

WRF767SDEM01 WHIRLPOOL

Model REFRIGERATOR

Near Bainbridge Township, OH 44023

Robert A.

Job Details: 01/24/2018

Cc doors not even, lights inside ff not turning on, rt shelf not even, corrected shelf, found no power to lights, needs led supply bd; ordrng 1 W10830288 (POWER SUPPLY LED), schdld next appmnt for 1/31 WED

We serviced a

KGCS166GSS09 KITCHENAID

Model COOK TOP

Near Pepper Pike, OH 44124

Robert A.

Job Details: 01/24/2018

Inspected unit, no burnt wires, need left front ofifice holder and screws; ordrng 2 WP3368921 (SCREW433)s and 1 WPW10155786 (ORIFICE HOLDER), schdld next appmnt for 1/31 WED

We serviced a

MHW6000XW2 MAYTAG

Model WASHER

Near Ravenna, OH 44266

Robert A.

Job Details: 01/24/2018

Cc eaking out bottom of door, found hair on glass, cleaned, checked boot, good, cc sound not working, checked connections, good, needs ui, Ran diognastics F0e1 load detected in clean cycle, ran diognastic cycle, good, needs ui; ordrng 1 W10387857 (PANEL NLA),

We serviced a

KRFC302ESS00 KITCHENAID

Model REFRIGERATOR

Near South Russell, OH 44022

Robert A.

Job Details: 01/24/2018

Installed mullion, leveled unit, op test ok; Job Cmpltd

We serviced a

KECC508RPB04 KITCHENAID

Model COOK TOP

Near Pepper Pike, OH 44124

Robert A.

Job Details: 01/24/2018

Installed and tested rt front element, op test ok; Job Cmpltd

We serviced a

AMV2307PFS0 AMANA

Model MICROWAVE

Near Middlefield, OH 44062

Robert A.

Job Details: 01/24/2018

Found exhaust fan not plugged in, plugged in, tested fan good, tested unit with cup of water, heating, good, op test ok; Job Cmpltd

We serviced a

FFGF3047LSH FRIGIDAIRE

Model RANGE

Near Cleveland Heights, OH 44121

Tim G.

Job Details: 01/24/2018

Complaint that the unit was displaying a error code. Tested a bake and found the ignitor to come on and the gas valve to open. Allowed unit to preheat and found no error. Asked customer if it was a F11 which is a stuck or shorted key which was duplicated on purpose by the Tech and the customer said it was a different number. Unit cycled 2 more times and maintained the temp without throwing the error code. Tech advised the customer to take a picture of the display if the error should reappear. Office to run CC; Job Cmpltd

We serviced a

SBD20NW AMANA

Model REFRIGERATOR

Near Willoughby Hills, OH 44094

Corina B

Job Details: 01/24/2018

Replaced the im and fill cup. Optest ng. Checked the wires to the im, replaced the fused in the harness was open, replaced the fuse, good. Wires to the im have continuity. There is no voltage to the im. Door switches are good. There is a broken wire in the cabinet.

We serviced a

WRS588FIHW00 WHIRLPOOL

Model REFRIGERATOR

Near Gates Mills, OH 44040

Corina B

Job Details: 01/24/2018

CC that the is a loud sound. Cust has video of the sound. It's the damper door opening and closing. Will need a new damper door. Called SM to order part ; ordrng 1 W11164593 (DIFFUSER), schdld next appmnt for 1/31 WED

We serviced a

MFI2569YEM0 MAYTAG

Model REFRIGERATOR

Near Cleveland, OH 44111

Dan

Job Details: 01/24/2018

Installed new user interface, op test good ; Job Cmpltd

We serviced a

ED5FHEXTT00 WHIRLPOOL

Model REFRIGERATOR

Near Cleveland, OH 44111

Dan

Job Details: 01/24/2018

Customer complaint of ice build up in freezer section and water leaking on floor, found ice maker fill tube frozen solid, found water seeping passed fill valve, unit needs new fill valve, installed new fill valve and cleared fill tube, op test good ; used 1 W10408179 (VALVE-INLET) from stock, Job Cmpltd

We serviced a

RBS245PRS00 WHIRLPOOL

Model WALL OVEN

Near Brooklyn, OH 44144

Dan

Job Details: 01/24/2018

Customer complaint that screws that hold control in are falling out, screws are not correct size for control, but were reinstalled because that’s where they came from, removed incorrect screws, installed bigger screws, op test good ; Job Cmpltd

We serviced a

RBS245PRS00 WHIRLPOOL

Model WALL OVEN

Near Brooklyn, OH 44144

Dan

Job Details: 01/24/2018

We serviced a

MED7500YW2 MAYTAG

Model DRYER

Near Cleveland Heights, OH 44106

Tim G.

Job Details: 01/24/2018

Complaint that the unit doesn’t heat. Checked unit and found 240vac present. Checked and found no power to the element and the TOD open. Bypassed TOD and found element to still not work. Unit needs the timer and TOD. Cust has a foil accordian style vent hose attached to dryer (see pic). Explained the fire hazard associated with this type of vent hose and advised cust to replace with a semirigid metal hose to prevent fire hazard.; ordrng 1 WPW10404695 (timer) and 1 WPW10625430 (thermostat), schdld next appmnt for 1/31 WED

We serviced a

MVWX655DW1 MAYTAG

Model WASHER

Near Shaker Heights, OH 44120

Tim G.

Job Details: 01/24/2018

Complaint that the unit is not cycling. Checked and found a F8E1 long or no fill. Checked and found no cold water pressure. Found the cold water turned off. Customer just bought home and was not aware of the shutoff in the basement that states to close when in the winter. Turned the water on and tested, op test good. Ran recal cycle, op test good. ; Job Cmpltd

We serviced a

WRX988SIBM03 whirlpool

Model refrigerator

Near North Ridgeville, OH 44039

Paul H.

Job Details: 01/24/2018

Replace Evap fan,and support fan,opt test good ; Job Cmpltd,

We serviced a

MVWC416FW0 maytag

Model washer

Near Cleveland, OH 44109

Chad P.

Job Details: 01/24/2018

Confirmed agitator stripped again. Installed new wash plate and agitator. Applied threadlocker to bolt that secures it. Op test ok. ; Job Cmpltd,

We serviced a

AGR5330BAW3 amana

Model range

Near Garfield Heights, OH 44105

Chad P.

Job Details: 01/24/2018

Cc that unit gets hot to the touch and sets off fire alarm down in the basement ran unit on bake at 350 then 400. Op test ok. Advised the unit is so new that it is burning off residue from the manufacturing process. This is normal and with regular use it will go away. Op test ok. ; Job Cmpltd,

We serviced a

WMH53520CS7 whirlpool

Model microwave

Near WARRENSVL HTS, OH 44122

Chad P.

Job Details: 01/24/2018

Cover up burn marks. Touch up was not a perfect match but Cust was okay with it. Op test ok. ; Job Cmpltd,

We serviced a

MVWX655DW1 maytag

Model washer

Near Cleveland, OH 44134

Chad P.

Job Details: 01/24/2018

Found unit shut down it’s pump running constantly. Likely suds fault. Held cancel button and unit shut down pump and resumed normal op. Ran calibration and service test mode. Op test ok.

We serviced a

RTW4640YQ01 roper

Model washer

Near Brooklyn, OH 44144

Chad P.

Job Details: 01/24/2018

Found suspension weak. Tub is bouncing up and down. Needs suspension replaced. Ran service test mode. No other faults. ; ordrng 1 W10780048 (SUSPENSION),

We serviced a

WFW92HEFW0 whirlpool

Model washer

Near Painesville Township, OH 44077

Jeff M

Job Details: 01/24/2018

The water lines are leaking. I tighten the hot water line does not leak the cold keeps leaking. Water lines are three years old told the customer to replace them and he will be fine; Job Cmpltd

We serviced a

RF386PXGQ WHIRLPOOL

Model RANGE

Near Highland Heights, OH 44143

Corina B

Job Details: 01/24/2018

Replaced the switches. The left rear switch sticks out about .25" farther then the others. Optest ok; used 1 SHIPPING (SHIPPING AND HANDLING) from stock, Job Cmpltd

We serviced a

WTW7300DW1 WHIRLPOOL

Model WASHER

Near Willoughby, OH 44094

Corina B

Job Details: 01/24/2018

Replaced the control. Ran a calibration. Optest ok. ; Job Cmpltd

We serviced a

MVWX655DW1 maytag

Model washer

Near Perry, OH 44081

Jeff M

Job Details: 01/24/2018

I ran a test cycle and a drain and spin cycle I can’t find the sound unit tested good ; Job Cmpltd,

We serviced a

WTW4850XQ0 WHIRLPOOL

Model WASHER

Near Mentor, OH 44060

Corina B

Job Details: 01/24/2018

CC that the unit does not spin out. Ran diag F8E1 – NO FILL, LONG FILL. Cleared code. Ran manual test for cold and hot, good. Ran a normal wash and a drain and spin with bath towels. Advised cust to use 1-2 tablespoons of detergent. 6-8 bath towels equals 1 load. Optest ok. ; Job Cmpltd

We serviced a

MEDX655DW1 maytag

Model dryer

Near Perry, OH 44081

Jeff M

Job Details: 01/24/2018

Installed new part unit op tested good ; Job Cmpltd

We serviced a

WEG745H0FH0 WHIRLPOOL

Model RANGE

Near Shaker Heights, OH 44120

Dan

Job Details: 01/24/2018

Installed new ignitor, op test good ; Job Cmpltd

We serviced a

NTW4516FW1 WHIRLPOOL

Model WASHER

Near Cleveland Heights, OH 44118

Dan

Job Details: 01/24/2018

Customer complaint that unit cuts on and just starts humming, ran diagnostics found f8e1(long/no fill) error code, started normal wash cycle, unit filled and advanced to wash cycle, ran bulky wash cycle, unit filled and over flowed, repeated with same results, pressure hose is clear, unit needs new control; ordrng 1 W11124710 (CNTRL), schdld next appmnt for 1/31 WED

We serviced a

MVWB855DC1 whirlpool

Model washer

Near North Ridgeville, OH 44039

Paul H.

Job Details: 01/24/2018

Replace CNTRL kit, running a diagnostics test,; Job Cmpltd

We serviced a

WTW5000DW1 WHIRLPOOL

Model WASHER

Near Maple Heights, OH 44137

Tim G.

Job Details: 01/24/2018

Complaint is with the units lid lock. Customer stated that the unit only locks when it spins. Checked unit for errors and found none stored. Tested the lid lock I manual test mode and found to operate good. Ran auto test cycle and found to complete without error. Tested the unit I a normal cycle and found the lid lock functioning properly (this model unit locks when in spin to make add garments easier). Instructed customer on function and to use no more than 2tbls of detergent. ; Job Cmpltd

We serviced a

WRF757SDEM01 whirlpool

Model refrigerator

Near Elyria, OH 44035

Paul H.

Job Details: 01/24/2018

Replace harness and cover Evap,running diagnostics test,good ; Job Cmpltd,

We serviced a

KDTE254ESS2 KITCHENAID

Model DISHWASHER

Near Solon, OH 44139

Tim G.

Job Details: 01/24/2018

Complaint that the unit isn’t draining completely. Checked unit and found full of water, tried a cancel drain and found pump to not come on. Checked for power at pump and found 120vac. Plugged pump back in and found to work then not. Pulled connection and squeezed connector together to make a tighter connection, op test good. Suggested to customer to use Finish or Affresh dishwasher cleaner to eliminate the oder from the standing water. ; Job Cmpltd

We serviced a

MFI2067AES WHIRLPOOL

Model REFRIGERATOR

Near South Russell, OH 44022

Tim G.

Job Details: 01/24/2018

Complaint that the unit is not making ice and everything in the ff is freezing. Checked and found temps in the ff between 31-33degs. Found service pointer 4317470 stating that if the unit is not hooked up to water and the ice maker is in the on position it will cause more cold air into the ff section. Checked and found the fill tube frozen causing the unit to not make ice and the freezing in the ff. Thawed fill tube and found unit needing ice maker due to flaking from the mold and the fill valve due to seeping. ; ordrng 1 67006322 (water inlet valve) and 1 W10583817 (icemaker), schdld next appmnt for 1/31 WED

We serviced a

MVWX655DW1 maytag

Model washer

Near Parma, OH 44130

Macaulay G.

Job Details: 01/24/2018

Replaced main control board. Calibrated and tested ok.; Job Cmpltd,

We serviced a

WFC310S0ES1 WHIRLPOOL

Model RANGE

Near Cleveland, OH 44120

Dan

Job Details: 01/24/2018

Installed new control, op test no good, found a leg of power supply cutting in and out, advised customer that they need an electrician to correct power supply ; Job Cmpltd

We serviced a

MVWX655DW1 MAYTAG

Model WASHER

Near Shaker Heights, OH 44120

Dan

Job Details: 01/24/2018

Installed new control, ran re-calibration cycle, op test good, also noticed customer has foil style vent tube connected to dryer, advised customer that this is a potential fire hazard and they should replace it with a rigid metal or solid metal vent tube ; Job Cmpltd

We serviced a

MVWB765FW1 WHIRLPOOL

Model WASHER

Near Mayfield Heights, OH 44124

Corina B

Job Details: 01/24/2018

Replaced the dispenser. Optest ok. ; Job Cmpltd

We serviced a

WRX735SDBM03 WHIRLPOOL

Model REFRIGERATOR

Near Lyndhurst, OH 44124

Corina B

Job Details: 01/24/2018

Icemaker came broken. Replaced the Im from ts. Optest ok. ; used 1 SHIPPING (SHIPPING AND HANDLING), and 1 W10377151 ([Alt for W10882923) Job Cmpltd

We serviced a

MVWB835DW1 maytag

Model washer

Near North Ridgeville, OH 44039

Paul H.

Job Details: 01/24/2018

, Replace user interface,and control board,running a diagnostics test pass all good ; Job Cmpltd,

We serviced a

MFI2569VEQ2 whirlpool

Model refrigerator

Near North Ridgeville, OH 44039

Paul H.

Job Details: 01/24/2018

Valve chatter and no ice, low pressure at filter, cycled valve a couple of times, no change, bypassed filter, pressure good, no more chatter, ice production should return to normal; Job Cmpltd

We serviced a

MEDB755DW2 MAYTAG

Model DRYER

Near Cleveland, OH 44110

Corina B

Job Details: 01/23/2018

CC that the clothes are coming out wet and there is no lint on the screen. customer has foil style vent tube connected to dryer, advised customer that this is a potential fire hazard and they should replace it with a rigid metal or solid metal vent tube. Turned unit on checked the vent outside, no air flow. The temp on the unit was on low heat. Optest ok. ; Job Cmpltd

We serviced a

MVWX655DW0 maytag

Model washer

Near Avon Lake, OH 44012

Paul H.

Job Details: 01/23/2018

They were 2 errors code on too much soap and un level clear then both,run diagnostics test,no good is not shifting it has a bad hub ; ordrng 1 W10528947 (hub)

We serviced a

AEQ6700FS0 frigidaire

Model dryer

Near Geneva, OH 44041

Jeff M

Job Details: 01/23/2018

The unit is not heating I tested all the fuses they tested good I tested the heating element it is open. EST only cust needs to think on it ; ordrng 1 131553900 (heater-housing assy)

We serviced a

MRT311FFFH00 MAYTAG

Model REFRIGERATOR

Near Cleveland Heights, OH 44118

Corina B

Job Details: 01/23/2018

CC that the door squeaks. Removed door used Vaseline the door hinges. Optest ok. ; Job Cmpltd

We serviced a

ICI500XB00 IKEA

Model COOK TOP

Near Cleveland, OH 44113

Dan

Job Details: 01/23/2018

Installed user interface, induction control board and harness, op test good ; Job Cmpltd

We serviced a

KDTM504EPA0 KITCHENAID

Model DISHWASHER

Near WARRENSVL HTS, OH 44122

Tim G.

Job Details: 01/23/2018

Complaint that the unit is leaking. Checked the unit and found the inlet valve to have froze (unit on a outside wall) and crack. Unit needs valve and the customer was given a estimate just in case the warranty won’t cover. Also the mod and set provided are not matching. Customer to contact whirlpool to get corrected. ; Job Cmpltd

We serviced a

KITCHENAID DISHWASHER

Model KUDS30IXBL6

Near Parma, OH 44130

Gail V.

Job Details: 01/23/2018

Replaced all 4 dishwasher rack wheels, support arm piece and bearing, and sump motor. Tested unit. All tested ok. ; Job Cmpltd,

We serviced a

KSC23C8EYY02 WHIRLPOOL

Model REFRIGERATOR

Near Cleveland, OH 44120

Corina B

Job Details: 01/23/2018

CC that the unit is not cooling. Ff 50 fz 5. Ff evap is covered in ice. Steamed ff evap out. Replaced the ff evap thermistor from t/s. Replaced the wrong thermistor the first. Optest ok. ; used 1 W10902214 (THERMISTOR) from stock, Job Cmpltd

We serviced a

WDT720PADM3 WHIRLPOOL

Model DISHWASHER

Near Moreland Hills, OH 44022

Tim G.

Job Details: 01/23/2018

Complaint that the unit isn’t filling with water and that the upper rack keeps falling. Found the float stuck in the up position causing the unit to not fill. Advised the customer to use no more than 2tbls of detergent. Installed upper rack wheels, op test good. ; Job Cmpltd

We serviced a

WFE515S0ES1 WHIRLPOOL

Model RANGE

Near Cleveland, OH 44102

Eric M.

Job Details: 01/23/2018

Installed hinges and receivers, op test good ; Job Cmpltd

We serviced a

WHIRLPOOL REFRIGERATOR

Model MFI2067AES

Near Parma, OH 44129

Macaulay G.

Job Details: 01/23/2018

Replaced start device. Tested and started ok. ; Job Cmpltd,

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FGHC2342LF3

Near Cleveland, OH 44114

Brian B

Job Details: 01/23/2018

Replaced solenoid and container. Tested unit. Cube solenoid still not energizing. Checked voltage on solenoid. 45 volts when paddle is pressed. Board was damaged when solenoid shorted out. Will also need main board replaced. Office to order part. Will r/s customer. Ship part to same as before attn: James.; ordrng 1 5304499075 (MAIN BOARD 14343), schdld next appmnt for 1/31 WED !,

We serviced a

WHIRLPOOL DRYER

Model WGD4815EW2

Near Aurora, OH 44202

Robert A.

Job Details: 01/23/2018

Found valve not opening, checked coil, ng needs coil; ordrng 1 WPW10328463 (COIL), schdld next appmnt for 1/31 WED !,

We serviced a

JFC2290VEM8 jennaire

Model refrigerator

Near Bay Village, OH 44140

Paul H.

Job Details: 01/23/2018

IM heater has failed, IM needs replaced, replaced t/s, cycled and filled, op test ok.; used 1 W10884390 (ICE MAKER ASSY) from stock

We serviced a

KSF26C6XYY04 kitchenaid

Model refrigerator

Near Avon Lake, OH 44012

Paul H.

Job Details: 01/23/2018

Call Techline spoke to Joel, SR# 7721116259, being reviewed by Whirlpool for non-repairable, will contact us or customer in 48-72 hours.

We serviced a

WTW8500DC1 whirlpool

Model washer

Near Rocky River, OH 44116

Paul H.

Job Details: 01/23/2018

Checking for squeaking noise,there is water damage on gear case,ordering gear case ; ordrng 1 W10811956 (gearcase)

We serviced a

GTWN2800DW ge

Model washer

Near Perry, OH 44081

Jeff M

Job Details: 01/23/2018

Turn the washer on ran through the cycles I explain to the customer the noise it was making is the mode shifter. I explained this style washer has metal splines that locked together which makes this loud but not a bad thing.; Job Cmpltd

We serviced a

JVM1540DN1WW ge

Model microwave

Near Wickliffe, OH 44092

Jeff M

Job Details: 01/23/2018

The Control panel is unresponsive after a few seconds it will display shorted channel. The unit needs a new panel ; ordrng 1 WB56X10824 (assy-cont pnl bq),

We serviced a

WHIRLPOOL WASHER

Model MVWB880BW0

Near Parma, OH 44134

Macaulay G.

Job Details: 01/23/2018

Replaced suspension rods in washer. Tested ok.; used 1 SHIPPING (SHIPPING AND HANDLING) from stock, Job Cmpltd,

We serviced a

WHIRLPOOL DRYER

Model WGD4815EW2

Near Aurora, OH 44202

Robert A.

Job Details: 01/23/2018

Found valve not opening, checked coil, ng needs coil; ordrng 1 WPW10328463 (COIL), schdld next appmnt for 1/31 WED !,

We serviced a

WHIRLPOOL DRYER

Model FAQE7001LW0

Near Streetsboro, OH 44241

Robert A.

Job Details: 01/23/2018

Ran diognastics e5b heater fault. E25 control ntc open circuitOhmed heater, open, checked control found shorted, see pic needs heater asm and controlVenting to outside should be checked/cleanedCust Has a foil accordian style vent hose attached to dryer (see pic). Explained the fire hazard associated with this type of vent hose and advised cust to replace with a semirigid metal hose to prevent fire hazard.Please quote; ordrng 1 137032600 (LIMIT20.33) and 1 137070890 (CONTROL172.75) and 1 137114000 (ELEMENT163.48) and 1 3204267 (TSTAT50.54), used 1 SHIPPING (SHIPPING AND HANDLING) from stock, schdld next appmnt for 1/31 WED ! [***],

We serviced a

WHIRLPOOL DRYER

Model WED4900XW0

Near Streetsboro, OH 44241

Robert A.

Job Details: 01/23/2018

, Ran unit, found unit not heating, checked vent, clogged, cut off open, jumped out unit heating, replaced, op test okVenting needs cleaned, clogged in wallDo not use until vent is cleaned; used 1 279816 (CUTOFF41.15) from stock, Job Cmpltd,

We serviced a

KSSS42QDX04 KITCHENAID

Model REFRIGERATOR

Near Moreland Hills, OH 44022

Tim G.

Job Details: 01/23/2018

Complaint that the unit doesn’t make ice. Checked ice maker and found to run when jumping T-H. Let unit cycle and found the valve to energize but not let any water in due to being blocked. Unit needs valve ; ordrng 1 W10853654 (valve-inlt), schdld next appmnt for 1/31 WED

We serviced a

GBD307PDS6 WHIRLPOOL

Model RANGE

Near Solon, OH 44139

Tim G.

Job Details: 01/23/2018

Installed new control, op test ng. Checked and found now not to have a display from the LCD screen. Tech pulled main control and found many weak and compromised soldering joints that when pulling connections to replace the UI something now is causing the main control to not come on.

We serviced a

LFBD2409LW0B FRIGIDAIRE

Model DISHWASHER

Near Cleveland, OH 44104

Dan

Job Details: 01/23/2018

Installed new door seals, op test good ; Job Cmpltd

We serviced a

WHIRLPOOL WASHER

Model LSN1000LW0

Near Kent, OH 44240

Robert A.

Job Details: 01/23/2018

Found coupler broken, spun trans by hand, good, replaced coupler, ran unit, op test ok; used 1 285753AXXX (XXXCOUPLINGXXXDONOTRESTOCK) from stock, Job Cmpltd,

We serviced a

FRIGIDAIRE STACK W/D

Model FLEB8200FS1

Near Cleveland, OH 44113

Macaulay G.

Job Details: 01/23/2018

Found vent disconnected. Pulled stack unit out and reconnected and taped vent. Ran test cycle. No leaks. Op test ok.;

We serviced a

MGR5775QDB MAYTAG

Model RANGE

Near University Heights, OH 44118

Corina B

Job Details: 01/23/2018

CC that the oven takes to long to heat. Heated oven to 350. Advised cust to calibrate the temp is on page 15 in owners manual. Showed how to calibrate the unit. When gas turns off there is a popping noise. Removed the panel. Turned the oven on with panel off, popping noise went away. Readjusted the panel. Ignitor 3.5 amps. Called tl Rick advised me that the popping sound is normal. Optest ok; Job Cmpltd

We serviced a

AMANA RANGE

Model AGR6603SFS0

Near Seven Hills, OH 44131

Macaulay G.

Job Details: 01/23/2018

Replaced cooktop. All functions are normal.; Job Cmpltd, s

Our Service

Our Training