Service History 364 - Fred's Appliance

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ00

Near Mantua, OH 44255

Brian M

Job Details: 06/04/2021

Cc unit not running lights all off then a day later lights came back on and freezer seems to be cooling Found freezer to be cool Ran test 3 found no power going to fans Checked HV board Needs board ; ordrng 1 W11224256 (cntrl-elec)

We serviced a

WHIRLPOOL WASHER

Model WTW8800YW0

Near Aurora, OH 44202

Brian M

Job Details: 06/04/2021

Cc unit not going through full cycle Found UI not responding to all selections during auto testing Ran manual pump found pump to hum then when I squeezed drain hose pump kicked on Some thing pushed through Ran several manual fills and drains Still not draining properly needs pump may need UI but UI is NLa if it is customer wants to try just the pump for now ; ordrng 1 WPW10409079 (pump-water) and 1 W10404674 (console)

We serviced a

KENMORE RANGE

Model 790.73433312

Near Garfield Heights, OH 44125

Dan H

Job Details: 06/04/2021

"Installed new igniter and seal, op test good"

We serviced a

KITCHENAID RANGE

Model KGRS505XSS05

Near Cleveland, OH 44144

Jason N

Job Details: 06/04/2021

"Cc unit knobs not working anymore, and a gas leak Confirmed 4 burner valves are seized up. Unit needs manifold. Found gas leak on manifold connection. Able to tighten fitting and stop leak. Customer also stated ovens dont always work properly. Ran bake tests on both upper and lower. Both igniters drawing approx. 2.6-2.7a , will also need oven igniters. ; ordrng 1 WPW10204705 (Manifold) and 2 12400035s"

We serviced a

WHIRLPOOL DRYER

Model n/a

Near Painesville, OH 44077

Jeff M

Job Details: 06/04/2021

This is a secondhand store for appliances I looked at for machines I charge the credit card to this one so I honestly dont know what four machines I looked at because all of them the bearings were shot and all the washers theres only two of them that I actually spent time looking at those are the two previous PVRs but everything was paid for on this one and everything is an estimate only

We serviced a

WHIRLPOOL RANGE

Model WFG320M0BW0

Near Lakewood, OH 44107

Corina B

Job Details: 06/04/2021

Replaced the glass. Optest ok.

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC704FBS02

Near Cleveland, OH 44102

Jason N

Job Details: 06/04/2021

"Installed door closer, ice door gasket and mullion. Door is closing much tighter with new closer. Door is sealing properly. Advised customer to monitor ice for excessive melting."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF954CIHZ03

Near Garfield Heights, OH 44128

Dan H

Job Details: 06/04/2021

"Customer has not received part yet, they need to be rescheduled when part has been delivered ; O-emld tckt"

We serviced a

GE DRYER

Model GTDP490ED0WS

Near Painesville, OH 44077

Jeff M

Job Details: 06/04/2021

Push the start switch failed estimate only; ordrng 1 WE4M416 (Start switch) and 1 S

We serviced a

GE DISHWASHER

Model DDT57SGF2BB

Near Painesville, OH 44077

Jeff M

Job Details: 06/04/2021

Installed the new part op tested good. Float switch

We serviced a

GE MICROWAVE

Model JVM3160DF4BB

Near Madison, OH 44057

Jeff M

Job Details: 06/04/2021

Installed the new part op tested good. Latch ASSY

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFHT1831QS6

Near Madison, OH 44057

Jeff M

Job Details: 06/04/2021

The lower crisper tray rack was not sitting in its proper spot causing the door to be pushed open and not close properly

We serviced a

WHIRLPOOL REFRIGERATOR

Model EB9SHKXVQ05

Near Avon, OH 44011

Gabriel P

Job Details: 06/04/2021

"Found ice maker not cycling replace from t/s ,opt test ok ; used 1 W10884390 (ICE MAKER ASSY), and 1 SENIORDISCOUNT (senior discount) from stock"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRB329DMBM02

Near Ashtabula, OH 44004

Jeff M

Job Details: 06/04/2021

The unit was making a noise I turn the icemaker off its not hooked up to water. Customer left the door open and there was zero frost inside the freezer upon my arrival

We serviced a

MAYTAG DRYER

Model MEDB835DW3

Near Aurora, OH 44202

Brian M

Job Details: 06/04/2021

Cc of noise Found idler pulley not spinning Replaced using dryer kit OP Test Ok ; used 1 4392067 (DRYER REPAIR KIT) from stock

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC302ESS02

Near Chagrin Falls, OH 44023

Brian M

Job Details: 06/04/2021

Installed gasket and mullion heater bInstalled valve OP Test Ok

We serviced a

WHIRLPOOL DRYER

Model WGD6620HC0

Near Euclid, OH 44132

Joe O

Job Details: 06/04/2021

"Installed control, ui, and moisture sensor harness. Ran test cycle. Op test ok"

We serviced a

WHIRLPOOL DISHWASHER

Model WDF520PADM7

Near Willoughby, OH 44094

Joe O

Job Details: 06/04/2021

Customer never received a spray arm. Part number for spray arm was the model number. Re ordering spray arm; ordrng 1 WPW10319027 (spray arm)

We serviced a

MAYTAG REFRIGERATOR

Model MFC2062FEZ03

Near Shaker Heights, OH 44122

Jason N

Job Details: 06/04/2021

"Cc unit not dispensing water, no ice production now.Tested water dispense, very little water coming out. Checked pressure in to unit. Low pressure from water saddle valve. Advised customer to contact plumber to have saddle valve replaced."

We serviced a

KITCHENAID RANGE HOOD

Model KVUB600DSS4

Near Avon Lake, OH 44012

Gabriel P

Job Details: 06/04/2021

Found bad connection and burn control ordering took pic of pop ; ordrng 2 W11109591 (Led light)s and 1 W11282990 (Control)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ

Near Avon, OH 44011

Gabriel P

Job Details: 06/04/2021

"When plug in unit ice maker was off jump start ice maker and it cycle to home position,working as design"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT314TFDW00

Near Rocky River, OH 44116

Corina B

Job Details: 06/04/2021

"Cust showed pop, sent pic. CC that the unit not cooling in the ff section. Found frost on the back wall of the freezer. Found gaps in the liner took pictures. Called t/l unit is non repairable."

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC604FSS01

Near Fairview Park, OH 44126

Corina B

Job Details: 06/04/2021

Checked pressure 0 low side high 30 psi. No gas in the system. Used nitrogen with soap no bubbles found. Called t/l unit is non repairable.

We serviced a

WHIRLPOOL DRYER

Model WED4815EW1

Near Cleveland, OH 44111

Corina B

Job Details: 06/04/2021

CC that the unit is not heating. Checked the terminal block l1 to n 120 volts l2 to n 120 volts. L1 to l2 0 volts. Checked the outlet has 240 volts. When running the dryer the outlet was making popping noises. Advised cust to to replace the outlet. Unit started to heat. Optest ok.

We serviced a

MAYTAG WASHER

Model MVW7232HW0

Near Westlake, OH 44145

Dan H

Job Details: 06/04/2021

"Customer complaint that unit stops in rinse cycle and just continues to drain and fill but never spins the load out, confirmed, unit was stuck at 30 minutes in rinse cycle and would not advance, unit needs new control, part is out of stock so not scheduling return appointment ; ordrng 1 W11419171 (Cntrl)"

We serviced a

KITCHENAID COMPACTOR

Model KTTS505ESS0

Near Solon, OH 44139

Brian M

Job Details: 06/04/2021

Cc unit not functioning properly Found solid cycle switch not selected all the way on or off Hit switch OP Test Ok

We serviced a

WHIRLPOOL DISHWASHER

Model WDF520PADM9

Near Chagrin Falls, OH 44023

Brian M

Job Details: 06/04/2021

Cc unit leaving water on silverware Unit functioning properly Advised on soap usage and jet dry and heated dry option

We serviced a

WHIRLPOOL WASHER

Model WFW5620HW2

Near Broadview Heights, OH 44147

David R

Job Details: 06/04/2021

"Cc drain pump making noise, have gotten FL error code low flow. Went into diagnostics, no error codes. All valves are working correctly, seems like a steady flow. Found drain pump vibrating, causing noise. There was padding around pump, moved different spot to dampen pump, good. Running different cycles. No error codes popping up. Straightened drain hose. Good. Op test ok.** if gets code again. Would order water valves W11316255, W11316256 and water level sensor"

We serviced a

MAYTAG WASHER

Model MVW7232HW0

Near Olmsted Falls, OH 44138

Marie V

Job Details: 06/04/2021

"Cc that the unit has a hole in the basket and impeller. Confirmed. Replaced basket, screw, , cap and impeller, ran calibration and auto test heard something on the drain pump , removed drain pump and found plastic Op test ok"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT318FZDM06

Near South Euclid, OH 44121

Jason N

Job Details: 06/04/2021

"Cc unit door has sharp edgesReplaced ff door using customer supplied pre Id part. Ensured no sharp edges on new door, as well as good gasket seal. Op test good"

We serviced a

WHIRLPOOL RANGE

Model WFG320M0BB2

Near Cleveland, OH 44111

Corina B

Job Details: 06/04/2021

Replaced the door. Optest ok. Name plate was not received. Cust can install. ; ordrng 1 Wpw10481433 (Nameplate)

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF507HPS01

Near Cleveland, OH 44135

Corina B

Job Details: 06/04/2021

Replaced the ice maker. Cycled. Optest ok.

We serviced a

KITCHENAID COOKTOP ELE

Model KCGS950ESS02

Near Broadview Heights, OH 44147

David R

Job Details: 06/04/2021

Replaced burner heads. All except FR one. Tested. Good. Op test ok

We serviced a

WHIRLPOOL WASHER

Model WTW5105HW0

Near Westlake, OH 44145

Marie V

Job Details: 06/04/2021

"Took POP. Cc that they where washing sheets and when they came to check unit was showing to call for service and that it was still wet and then it was making a scraping noise. Ran diag found error code of f0e9 OB PAUSE F0e5 off balance load. Deleted error codes and ran an auto test. Confirmed noise it comes from the belt. Also from agitator as well. Found some change in between the agitator removed and replaced belt from T/S. Ran auto test again, op test ok; used 1 WPW10006384 (BELT) from stock"

We serviced a

AMANA WASHER

Model NTW4605EW0

Near Cleveland, OH 44108

Jason N

Job Details: 06/04/2021

"Cc unit not powering onRan diagnostics, found code f5e1 for lid switch fault. Ran auto test and calibration. All functions passed. Started normal cycle. All functions working properly, could not duplicate a power up issue."

We serviced a

JENN-AIR RANGE

Model JES9800CAB00

Near Westlake, OH 44145

Marie V

Job Details: 06/04/2021

"Replaced control board and oven sensor. Turned unit back on and preheated to 350*. Took temps. Op test ok tried to set the date it will not save the sate, just the time. Called whirlpool tech line spoke with Ritch told me that is possible that that has been taken out of the control or to replace control again and if it does not work then is not available anymore. No core for return ; ordrng 1 Wp8507p234-60 (Control) and 1 Wp8507p234-60 (Control)"

We serviced a

WHIRLPOOL WALL OVEN

Model WOS51EC7HS01

Near Mayfield, OH 44143

Dan H

Job Details: 06/04/2021

"Installed new cooling fan, op test good"

We serviced a

KITCHENAID COMPACTOR

Model KTTS505ESS0

Near Solon, OH 44139

Brian M

Job Details: 06/04/2021

Cc unit not functioning properly Found solid cycle switch not selected all the way on or off Hit switch OP Test Ok

We serviced a

SAMSUNG DRYER

Model DV363EWBEUF/A1

Near Mentor, OH 44060

Joe O

Job Details: 06/04/2021

Installed thermal cut off. Ran test cycle. Op test ok; used 1 SHIPPING (shipping and handling) from stock

We serviced a

WHIRLPOOL WASHER

Model WTW8500BR0

Near Cleveland, OH 44112

Jason N

Job Details: 06/04/2021

"Cc unit not washing/draining properlyRan diagnostics, found code f70 for overload. Ran auto test, basket not uncoupling from hub. Pulled basket, cleaned up hub and drive shaft. Reinstalled basket, reran auto test. ; ordrng 1 W10820039 (Hub) and 1 W10440786 (Suspension springs)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model MRT711SMFZ

Near Solon, OH 44139

David R

Job Details: 06/04/2021

Replaced FF door. Good. Op test ok

We serviced a

MAYTAG WASHER

Model MVWC565FW2

Near Strongsville, OH 44136

David R

Job Details: 06/04/2021

"Replaced shifter. Ran diagnostics, good. Op test ok"

We serviced a

GE DRYER

Model GTD33EASK0WW

Near Painesville, OH 44077

Joe O

Job Details: 06/04/2021

"Cc: thumping noiseRan test cycle. Found belt slipping on edge of motor pulley, causing belt to jump. Needs belt, idler pulley, and pulley cap. Cap shows out of stock. Office to reschedule; ordrng 1 WE12M29 (belt drive) and 1 WE12X20395 (idler pulley) and 1 WE2M96 (nut cap)"

We serviced a

SAMSUNG DRYER

Model DV45K6200EZ/A3

Near Avon, OH 44011

Gabriel P

Job Details: 06/04/2021

"Found pulley broken off ordering part do not have in truck stock ; ordrng 1 DC93-00634A (Idler), used 1 DC93-00634A (Dont have any), and 1 SHIPPING (shipping and handling) from stock"

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC704FPS04

Near Moreland Hills, OH 44022

Brian M

Job Details: 06/04/2021

Cc unit leaking all over dent in door and auger not working Called whirlpool Did a video call Ohmed thermistor it at 13 k ohms Whirlpool suggested to replaceGf2 rear board; ordrng 1 W11449015 (Door) and 1 W11330486 (Ui) and 1 W11228132 (shaft) and 1 W11450890 (Board)

We serviced a

WHIRLPOOL BUILT IN OVEN

Model RBD275PRB00

Near Euclid, OH 44117

Jason N

Job Details: 06/04/2021

"Cc unit oven control not working Customer stated all functions work, but display is not working. Confirmed display not illuminated. Checked connectors, all checked good. Unit needs control board, Control board (8303883) is NLA. ; ordrng 1 8303883 (Control board)"

We serviced a

WHIRLPOOL DRYER

Model WGD7500GW0

Near Lyndhurst, OH 44124

Corina B

Job Details: 06/04/2021

"CC that the unit stopped heating. Confirmed. Found the thermal cutoff open. Jumped the fuse, started to heat. Found the flame going over the burner funnel. Re adjusted the funnel. Flame is now good. Will need the thermal fuse. ; ordrng 1 WP8573713 (Thermal fuse)"

We serviced a

KITCHENAID REFRIGERATOR

Model KBFN502EBS02

Near Newbury Township, OH 44065

Brian M

Job Details: 06/04/2021

Replaced leds on right side

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF560SEHZ00

Near Grafton, OH 44044

David R

Job Details: 06/04/2021

"Cc unit gasket is not closing. Found door off alignment, correctly. Door sitting closer to cabinet now, also used hot gun to conform gasket around door. Closer and tighter on cabinet. Leave door closed for about half an hour to conform correctly. Unit is good. Op test ok."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF989SDAM00

Near Avon, OH 44011

Gabriel P

Job Details: 06/04/2021

Found a leak in the evaporator also is not coated compressor is loud fine a service pointer with a full repair; ordrng 1 W10687098 (Evap) and 1 W10143759 (Uv) and 1 WPW10537710 (Drip pan) and 1 W10276644 (Compressor)

We serviced a

MAYTAG WASHER

Model MVW6200KW0

Near Lorain, OH 44052

Gabriel P

Job Details: 06/04/2021

Found out f3e2 error pressure sensor blow threw pressure hose is clear call senior tech bj he help diagnose unit much deeper and will need control and the encoder ordering ; ordrng 1 W11481108 (Control) and 1 W11481116 (Control) and 1 W11406492 (Fascia)

We serviced a

KITCHENAID BEVERAGE CENTER

Model KUBL304ESS01

Near Avon, OH 44011

Marie V

Job Details: 06/04/2021

"Cc that the door is warped . Took pics, unit will need new door. Adv cust that the door takes 6-8 weeks to arrive and when it does to inspect is see something thats not right to give us a call; ordrng 1 W11522053 (Door right hand (stainless ))"

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFTR2021TW1

Near Willoughby Hills, OH 44094

Dan H

Job Details: 06/04/2021

"Customer complaint that unit is not cooling, freezer section temperature at -22 degrees, fresh food section temperature at 55 degrees, evaporator fan is not running, evaporator fan is receiving 120vac , unit needs new evaporator fan motor, customer will install themselves ; ordrng 1 242077705 (Fan motor), used 1 SHIPPING (shipping and handling) from stock"

We serviced a

WHIRLPOOL WASHER

Model WFW9620HC0

Near Mentor, OH 44060

Joe O

Job Details: 06/04/2021

"Cc: stuck in wash cycle, long cyclesFound no stored error codes. Found service pointer for this issue. Found hot and cold reversed. Customers supply valve is broken. Needs water lines swapped."

We serviced a

WHIRLPOOL REFRIGERATOR

Model Wrf993fifm00

Near Painesville, OH 44077

Joe O

Job Details: 06/04/2021

"Installed control, and evap cover. Unit is cooling. Advised customer to allow 24 hours for temps to adjust. Op test ok"

We serviced a

WHIRLPOOL WASHER

Model WFW75HEFW0

Near Perry, OH 44081

Joe O

Job Details: 06/04/2021

"Cc: f9e1 error, not spinningMS tag is not completely readable. Spoke with BJ, Found model number for unit. Found error codes f9e1(long drain), f3e1(water level system error), f8e3(overflow condition). Ran quick diagnostics cycle. Drain pump has good pressure. Pressure sensor is functioning. Needs controlCustomer does not want to repair at this time; ordrng 1 W11201274 (cntrl-elec), used 1 SHIPPING (shipping and handling) from stock"

We serviced a

WHIRLPOOL WASHER

Model WTW5005KW0

Near Fairport Harbor, OH 44077

Dan H

Job Details: 06/04/2021

"Customer complaint that unit is not operating, unit unplugged, customer plugged in unit paused in rinse cycle, pressed start unit resumed cycle, ran diagnostics no error codes found, unit is operating as designed"

We serviced a

WHIRLPOOL RANGE

Model GGG388LXS02

Near Avon, OH 44011

Marie V

Job Details: 06/03/2021

Cc that the unit turns on but is not the proper temp. Tested unit and checked temp it was around 290* 255* all over put the kill a watt meter on unit and tested igniter is pulling 3.45 amps. Called BJ told me to let unit cycle a few times and verify temp. It was around 299* to 311*. Unit needs to be calibrated. Calibrated unit by 20 and it when up to 337* and 322* so I added 5*more. And tested unit. Op test ok.

We serviced a

WHIRLPOOL REFRIGERATOR

Model ED25QFXHW00

Near Strongsville, OH 44149

David R

Job Details: 06/03/2021

"Cc unit not cooling correctly. Found temp high in FF but FZ still keep cool. Checked and did not hear any fans running. Tested and found FZ fan is stalling and not rotating. Ordering fan motor.; ordrng 1 4389144 (Fan), used 1 SHIPPING (shipping and handling) from stock"

We serviced a

MAYTAG WASHER

Model MVWX655DW1

Near Cleveland, OH 44109

Dan H

Job Details: 06/03/2021

"Customer complaint that unit is not agitating, found wash plate stripped, unit needs new wash plate ; ordrng 1 W10902814 (Wash plate), used 1 SHIPPING (shipping and handling) from stock"

We serviced a

MAYTAG FREEZER UPRIGHT

Model MZF34X16DW04

Near Mentor, OH 44060

Dan H

Job Details: 06/03/2021

"Customer complaint of frost build up and warm temperatures, temperature at 0 degrees, found door gasket pulled out of groove at bottom, no damage, reinstalled, op test good"

We serviced a

WHIRLPOOL OTR MICROWAVE

Model WML55011HS3

Near Mentor, OH 44060

Dan H

Job Details: 06/03/2021

"Customer complaint of humming noise and unit is not heating , confirmed , magnetron is just humming very loud, unit needs new magnetron, customer does not want repair at this time ; ordrng 1 W11402082 (Mag), used 1 SHIPPING (shipping and handling) from stock"

We serviced a

WHIRLPOOL REFRIGERATOR

Model KSSC42QVS06

Near Bratenahl, OH 44108

Dan H

Job Details: 06/03/2021

"Customer complaint that ice bin is stuck, removed ice container, op test good"

We serviced a

WHIRLPOOL DISHWASHER

Model WDT970SAHZ0

Near Brooklyn, OH 44144

Dan H

Job Details: 06/03/2021

"Customer complaint that unit is not starting, unit is receiving 120vac , tightened wire nuts, user interface lit up , started normal wash cycle, unit filled and began washing, unit is operating as designed"

We serviced a

GE REFRIGERATOR

Model DFE28JMHCES

Near Ashtabula, OH 44004

Joe O

Job Details: 06/03/2021

"Cc: frost build up, not cooling in ff sectionFound error codes 0106(ff fan feedback missing when running). Found ff evap fan not running. Ran diagnostics fan test. Needs ff evap fan; ordrng 1 WR60X29099 (refrigerator fresh f), used 1 SHIPPING (shipping and handling) from stock"

We serviced a

WHIRLPOOL WASHER

Model WFW9620HC0

Near Mentor, OH 44060

Joe O

Job Details: 06/03/2021

"Cc: will not run through cycle, long cycleFound error code f0e2(oversuds). Ran quick test cycle. Ran quick wash cycle. Found excessive suds in unit. Advised customer on soap usage. Op test ok"

We serviced a

MAYTAG WASHER

Model MVWB765FW1

Near Elyria, OH 44035

Gabriel P

Job Details: 06/03/2021

Found error f8e1 long fill check valve in manual test notice no hot water coming to unit notice main hot valve turn off correct issue ran calibration and auto test pass

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC704FPS04

Near Mayfield Heights, OH 44143

Jason N

Job Details: 06/03/2021

"Cc unit not cooling Found compressor not running, ran test 38, compressor did not start. Checked compressor windings for resistance, checked within specs according to tech sheet. Customer stated unit stopped cooling after a power outage, possible main board or Orion board could be at fault. Ordering both boards. ; ordrng 1 W11336586 (Control board) and 1 W11393142 (Compressor)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX986SIHZ00

Near Avon, OH 44011

Marie V

Job Details: 06/03/2021

When arrived both handles where broken took pics will have to reorder took pics.; ordrng 1 W11175811 (Handle)

We serviced a

HOT POINT RANGE

Model RGB508PT3WH

Near Madison, OH 44057

Jeff M

Job Details: 06/03/2021

Gas valve regulator in the back of the oven is not opening fast enough sometimes it works sometimes it doesnt estimate only; ordrng 1 WB19K12 (Valve) and 1 S

We serviced a

KITCHENAID WALL OVEN

Model KEHC379JSS08

Near Moreland Hills, OH 44022

Jason N

Job Details: 06/03/2021

Installed oven door glass. Op test good

We serviced a

AMANA WASHER

Model NTW4516FW3

Near Brooklyn, OH 44144

Corina B

Job Details: 06/03/2021

"CC that the unit fills and does nothing but drains. Confirmed. Ran diagF8E3 OVERFLOW CONDITION, F7E5 SHIFTER FAULT, F1E1 MAIN CONTROL FAULT, F8E1 NO FILL, LONG FILL. Checked the pressure hose, clear, no kinks. Replaced the control. Washer not moving. Ran the tach not moving. Will need the shifter. Do not have the shifter on my truck. Office to reschedule ; ordrng 1 W10913953 (Shifter), used 1 W11170317 (MUST RETURN**CORE*CNTRL-ELEC), and 1 W10913953 (Shifter) from stock"

We serviced a

MAYTAG REFRIGERATOR

Model MTB1954ARW

Near Cleveland, OH 44111

Corina B

Job Details: 06/03/2021

Replaced the condenser fan. Optest ok.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHZ04

Near Jefferson, OH 44047

Brian M

Job Details: 06/03/2021

Cc gasket smashed Fixed gasket OP Test Ok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT106TFDB01

Near Andover, OH 44003

Brian M

Job Details: 06/03/2021

Cc unit not cooling Found unit to have no frost pattern but compressor running Unit is up on a stand will need 2 techs to move unit out Needs compressor and evap ; ordrng 1 WPW10507886 (compressor) and 1 W10836706 (evaporator) and 1 WPW10143759 (dryer)

We serviced a

WHIRLPOOL DISHWASHER

Model WDT720PADB2

Near Diamond, OH 44412

Brian M

Job Details: 06/03/2021

Called customer 20 min prior to arrival to start dishwasher Unit ran for 57 min could not visually see a leak Called land lord to state my findings

We serviced a

WHIRLPOOL DRYER

Model WED6620HC0

Near Willoughby, OH 44094

Joe O

Job Details: 06/03/2021

"Cc: lint backing up in blower housingCleared lint, ran test cycle. Unit has good heat and air flow. Op test ok"

We serviced a

AMANA DRYER

Model NED4600YQ1

Near North Ridgeville, OH 44039

Gabriel P

Job Details: 06/03/2021

"Found bird stuck in the blower housing clear out,opt test ok unit working as design"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF989SDAE00

Near Avon, OH 44011

Gabriel P

Job Details: 06/03/2021

Ran test 4 to open valve then Feed nitrogen did find any leak on dryer filter or compressor or on evaporator it may be internal check pressure before doing all that and it was 20 into a vacuum no refrigerant in it also temp was 53 degrees in both sections cannot be repair

We serviced a

WHIRLPOOL WASHER

Model WTW5100HC0

Near Elyria, OH 44035

Gabriel P

Job Details: 06/03/2021

"Replace bazel,opt test ok"

We serviced a

KENMORE WASHER

Model 110.20702 990

Near Madison, OH 44057

Jeff M

Job Details: 06/03/2021

The unit is not spinning. The lid switch was loose re-adjusted it op tested good

We serviced a

GE REFRIGERATOR

Model PSH25PSWCSS

Near Perry, OH 44081

Jeff M

Job Details: 06/03/2021

The unit is Keeping temperature in the freezer. 60? in the fridge the bottom of the fridge is 30? the top is 60. Fresh food evaporator fan has seized needs replaced; ordrng 1 WR60X29099 (Fan) and 1 S

We serviced a

KENMORE WASHER

Model 110.26832692

Near Willoughby, OH 44094

Joe O

Job Details: 06/03/2021

Installed lid switch. Ran test cycle. Op test ok

We serviced a

MAYTAG WASHER

Model MVW7232HW0

Near Elyria, OH 44035

Gabriel P

Job Details: 06/03/2021

"Ran diagnostics no error codes found,ran calibration and auto test pass no issue at the moment"

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS0

Near Kent, OH 44240

Brian M

Job Details: 06/03/2021

Cc of noise Ran unit could not duplicate an abnormal noise

We serviced a

MAYTAG DRYER

Model MGDP575GW

Near Strongsville, OH 44136

David R

Job Details: 06/03/2021

Unit in Salon. Cc unit not drying towels all the way or some stuff dry and others not. Long vent. Ran unit for 20 mins and watched. Timed flame cycling on/off. Cycled the whole 20 mins on high. Unit is heating correctly. Would advise of not overloading and making sure with a long vent that it might be more dry time needing to add on. Also would have someone check vent as well to make sure of no blockage. Unit is good. Op test ok.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ0

Near Streetsboro, OH 44241

Brian M

Job Details: 06/03/2021

Tightened handle OP Test Ok

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC704FPS03

Near Lakewood, OH 44107

Corina B

Job Details: 06/03/2021

"Replaced the oryan board, compressor did not turn on in step 38, 39 or 40. Will need an ff evaporator. CC that the water sometimes works and does not. Confirmed. Removed the filter, water filled a cup. Advised cust to replace the filter. ; ordrng 1 W11291123 (Evaporator) and 1 W11336586 (Board)"

We serviced a

MAYTAG REFRIGERATOR

Model MSC21C6MFZ00

Near Gates Mills, OH 44040

Joe O

Job Details: 06/03/2021

Installed door. Cycled ice maker. Op test ok

We serviced a

KITCHENAID REFRIGERATOR

Model KBSD608ESS01

Near Waite Hill, OH 44094

Joe O

Job Details: 06/03/2021

Installed led modules. Op test ok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ02

Near Streetsboro, OH 44241

Brian M

Job Details: 06/03/2021

Leveled door OP Test Ok

We serviced a

MAYTAG WASHER

Model MVWC565FW1

Near Pepper Pike, OH 44124

Jason N

Job Details: 06/03/2021

"Cc unit not spinning outRan diagnostics, found codes f5e2 for lid lock fault and f2e1 for stuck button. Ran manual lid lock test, lock will not engage. Unit needs lid lock. Replaced using truck stock. Ran auto test and calibration. Op test good. ; used 1 W11307244 (DOOR LOCK) from stock"

We serviced a

KITCHENAID RANGE

Model KSGG700ESS0

Near Seven Hills, OH 44131

Dan H

Job Details: 06/03/2021

"Customer complaint of white smoke from oven, started bake for 350 degrees, smoke is just oven coating that burns off on first use, unit is operating as designed"

We serviced a

WHIRLPOOL DRYER

Model WED4950HW0

Near Cleveland, OH 44122

Jason N

Job Details: 06/03/2021

"Cc unit still not heating Customer stated she replaced fuse. Checked power in to unit, still missing an L. Found incorrect fuse tapped in fuse socket. Advised customer to replace with correct fuse. Wrote down what type she will need on lbc."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRB322DMHV01

Near Seven Hills, OH 44131

Dan H

Job Details: 06/03/2021

"Customer complaint that ice is not falling into bin and fresh food section door swings open , leveled unit, ice maker is mounted properly, ice bin is in correct position, noticed very small ice cubes, increased fill time to make bigger cubes, op test good"

We serviced a

KITCHENAID WALL OVEN

Model KEBS277DBL6

Near Cleveland Heights, OH 44118

Jason N

Job Details: 06/03/2021

Installed upper thermostat. Ran bake test on upper and lower ovens to 300 degrees. Both ovens preheated. Op test good.

We serviced a

MAYTAG WASHER

Model MVWC400XW0

Near Westlake, OH 44145

Marie V

Job Details: 06/03/2021

"Cc that the unit lock the door starts to spin and then unlocks the door and shuts down. Confirmed. Ran diag found error code of F5E1 lid switch fault, F2E1 stuck key , F7E1 basket speed sensor fault , F7E7 motor unable to reach target RPM. Replaced latch and shifter from T/S calibrated unit. And started a normal cycle. Op test ok. ; used 1 WPW10006355 (ACTUATOR), and 1 W10404050 (LATCH) from stock"

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFTR1814QWA

Near Garfield Heights, OH 44125

Dan H

Job Details: 06/03/2021

"Customer complaint that unit is not cooling, fresh food section temperature at 60 degrees, freezer section temperature at 43 degrees, compressor and condenser fan are running, evaporator fan is running, partial frost pattern on evaporator, unit needs new compressor and evaporator, customer does not want repair ; ordrng 1 5303918274 (Evaporator) and 1 5303918659 (Compressor), used 1 SHIPPING (shipping and handling) from stock"

We serviced a

KITCHENAID DISHWASHER

Model KDPM604KPS0

Near Westlake, OH 44145

Marie V

Job Details: 06/03/2021

"Cc that the unit is not draining, you have to press cancel a few times to get it to drain and that it gave them an error code of F9E1. Uninstalled unit and removed drain pump. Found food residue and something like from a rag, cleared all out and verify the drain hose. Is good. Tested unit 5 times fill and drain to make sure no leaks and is clear for drain. Op test ok."

We serviced a

KENMORE WASHER

Model 110.22352511

Near Amherst, OH 44001

Gabriel P

Job Details: 06/03/2021

"Found shaft of gearcase broken giving estimate on what customer needs they will not repair ; ordrng 1 WPW10006384 (Drive belt) and 1 W11454734 (Gearcase) and 1 W10721967 (Cam), used 1 SHIPPING (shipping and handling) from stock"

Our Service

Our Training