Samsung microwave owners will be familiar with the typical sound their microwave makes. But what should you do when that familiar hum becomes louder or your microwave starts making rattling or thumping sounds? There are some easy fixes to this problem, while others require a little more investigation.
Where is the noise coming from? Is it at the base of the microwave, or is it a grinding sound coming from the back? Is the microwave still heating your food? Does the noise stop and start, or is it continuous? Follow this guide to diagnose and fix the problem.
This guide applies to the following models:
MR5471G
MR6471G
MU4270W
MW1010
MW3252T
MW4271G
SMH7174BCXAA
SMH7174CC/XAA
SMH7174WCXAA
SMH7174WEXAA
SMH7175BCXAA
SMH7175CCXAA
SMH7175WCXAA
SMH7178STDXAA
SMH7178STEXAA
SMH7185STGXAA
SMH9187BXAA
SMH9187STXAA
SMH9187WXAA
SMV9165BCXAA
SMV9165SCXAA
The high voltage capacitor inside the microwave can store a lethal amount of electricity, even after the microwave has been disconnected from the power for several months. To safely access electrical components in the microwave, the capacitor must be discharged.
Due to the risk of electrocution, it is recommended that the more complex issues be repaired by a trained microwave professional.
The first place to check is the turntable. Open the microwave door and check that the microwave plate is sitting securely on the turntable support. If that appears in place, take out the turntable support and examine it. If debris is caught in a roller or a roller is defective, this can cause a rattling or thumping sound.
If the turntable support or turntable plate is damaged, replace it with a new one.
While examining the turntable, also check the turntable motor coupler. This part attaches to the turntable motor to ensure the plate turns smoothly. A broken or dislodged motor coupler will cause your microwave to make a thumping or rattling sound.
The coupler can be accessed from inside the microwave oven, beneath the turntable plate. On some models, you may need to access the turntable coupler from the turntable motor cover underneath the microwave.
If the typical hum your microwave makes has become louder and the microwave is no longer heating your food, the likely cause is the magnetron. The magnetron produces the microwave energy that cooks the food. If you run the microwave on a low setting and the noise gets quieter, this also indicates the magnetron is at fault. Another symptom of a faulty magnetron is if the noise issue comes and goes, as this indicates the magnetron is engaging and then disengaging.
A faulty magnetron can be replaced; however, you should exercise caution. The microwave must be turned off, and the high voltage capacitor must be discharged. You will also need to remove the top panel of the microwave to gain access. It is recommended that you wear gloves to avoid cuts from the sharp metal edges.
A faulty diode will cause the same symptoms as a faulty magnetron. So before replacing the magnetron, it pays to check the diode. The diode is located near the magnetron, so the same care should be taken when examining it.
If you are experiencing a grinding noise coming from underneath the microwave, you most likely have a defective turntable motor. The turntable motor is responsible for rotating the turntable plate. A noisy microwave that is still heating also indicates a problem with the turntable motor (also the stirrer motor).
The turntable motor is easily accessed on most models by removing the cover panel underneath the microwave. You will need to turn the microwave on its side to access the cover panel. Be careful not to lose any screws inside the cabinet as you take the panel off. If you cannot access it from underneath, you will need to remove the microwave casing.
A grinding noise not coming from underneath the microwave points to a faulty stirrer motor. The stirrer motor powers a metal blade that is responsible for deflecting microwave energy randomly throughout the microwave. A noisy microwave that is still heating food is a good indication that the stirrer motor (or turntable motor) is causing the issue.
Rattling or clicking sounds coming from the rear of the microwave suggest the cooling fan may be obstructed. Sometimes debris can get into the cooling fan, or it can become dislodged. To check the cooling fan, you will need to remove the microwave top panel. Remember to exercise caution when accessing the cooling fan. If you need to remove other parts to access the fan, make sure the capacitor is discharged and the power is off. Taking photos to remember how to reassemble the microwave is also advised.
If the fan appears unimpeded, there may be an issue with the cooling fan motor.
A fan that is not spinning freely will likely require a new cooling fan motor. Make sure to exercise caution before examining the cooling fan motor.
While error codes on appliances can be annoying, you can often resolve them on your…
Since caps and other hats are designed to be worn daily, whether it's to keep…
When the nF error code, which stands for 'No Fill,' is displayed, it indicates that…
Kenmore Elite dryers are available in both gas and electric and are part of Kenmore’s…
You can find a microwave and an oven in most modern kitchens since they are…
Is your oven emitting a burning or charred odor during self-cleaning? If so, don't fret—in…